;--------------------------------------------------------------------------
;
;
;   PEEDI target configuration file
;
;   Alessandro Rubini
;
;   Supported devices   : nomadik 8815
;   Board               : 8815nhk
;

;--------------------------------------------------------------------------
; The following section contains licenses that are required for PEEDI to
; operate. These licenses must be filled before using this file.
; The [LICENSE] section may contain license keys for one or more PEEDIs.
;
;   Example:
;       [LICENSE]
;       KEY         = UPDATE_24MAY2010, 1111-1111-1111-1
;       KEY         = XXXXX, 2222-2222-2222-2
;
; The [LICENSE] section may point to an external file which contains
; license keys for one or more PEEDIs. The external file must include 
; the text [LICENSE] followed by all keys.
;
;   Example:
;		[LICENSE]
;		FILE = tftp://192.168.3.1/license.txt
;		or
;		FILE=eep:license.txt 
;		or 
;		FILE = ftp://user:password@192.168.3.1/license.txt
;
;
; PEEDI is shipped with license keys stored in "eep:license.txt" and 
; printed on a label on the bottom side of PEEDI.
;
[LICENSE]
FILE=eep:license.txt
;--------------------------------------------------------------------------

[DEBUGGER]
PROTOCOL = gdb_remote               ; gdb remote
REMOTE_PORT = 2000                  ; TCP/IP port

[TARGET]
PLATFORM = ARM

[PLATFORM_ARM]
JTAG_CHAIN = 4                      ; list of IR lenghts of all TAP controller in JTAG chain
JTAG_CLOCK = 5, 10000               ; JTAG Clock in [kHz] - 5kHz jtag clock for init operations and 10MHz for normal work
                                    ; Valid range: 5 - 33000
TRST_TYPE = PUSHPULL                ; type of TRST output: OPENDRAIN or PUSHPULL
RESET_TIME = 20                     ; lenght of RESET pulse in ms; 0 means no RESET
TIME_AFTER_RESET = 1000             ; time between releasing the reset and starting the jtag communication

CORE0 = ARM926E, 0, 0x7926041       ; TAP 0 is ARM926E  CPU
CORE0_STARTUP_MODE      = RESET     ; startup mode after reset:
                                    ;   if RESET than no code is executed after reset
                                    ;   if STOP,XX then the target executes code for XX period in ms.
                                    ;   if RUN then the target executes code until stopped by the telnet "halt" command

CORE0_BREAKMODE         = soft      ; default breakpoint mode for the debugger:
;CORE0_BREAKMODE         = hard      ; default breakpoint mode for the debugger:
                                    ;   soft - use software breakpoints
                                    ;   hard - use hardware breakpoints

CORE_BREAK_PATTERN      = 0xDFFFDFFF ; software breakpoint pattern

CORE0_INIT              = INIT_XLOADER ; init section
CORE0_ENDIAN            = little
CORE0_WORKSPACE_ADDR    = 0x00001000 ; start address of workspace for flash programmer
CORE0_WORKSPACE_LEN     = 0x10000    ; length of workspace in bytes

CORE0_PATH  = "tftp://192.168.3.1/"  ; default path

CORE0_FILE  = "test.bin", BIN, 0xC0000000


[INIT_XLOADER]
break add hard 0
go
wait 1000
break del all

[ORCO]
mem load nmdk-ub bin 0
go


[SERIAL]
BAUD=115200
STOP_BITS=1
PARITY=NONE
TCP_PORT= =0; 2023

[TELNET]
PROMPT = "ndk> "                    ; telnet prompt
;BACKSPACE=127                      ; comment out for autodetect

[DISPLAY]
BRIGHTNESS      = 20                ; LED indicator brightness
VOLUME          = 25                ; beeper volume


[ACTIONS]                           ; user defined scripts
AUTORUN        = 2                 ; executed on every target connect

1 = go
2 = u

[go]
reset
wait 500
go

[u]
halt
break del all
mem load nmdk-ub bin 0 ; 0x03f80000
go