;-------------------------------------------------------------------------- ; ; ; PEEDI sample target configuration file ; ; Ronetix ; ; Supported devices : LPC2138 microcontroller ; ; Revision : 1.5 ; ; Date : March 23, 2007 ; ; The file is delivered "AS IS" without warranty or condition of any ; kind, either express, implied or statutory. This includes without ; limitation any warranty or condition with respect to merchantability or ; fitness for any particular purpose, or against the infringements of ; intellectual property rights of others. ; ;-------------------------------------------------------------------------- ;-------------------------------------------------------------------------- ; The following section contains licenses that are required for PEEDI to ; operate. These licenses must be filled before using this file. ; The [LICENSE] section may contain license keys for one or more PEEDIs. ; ; Example: ; [LICENSE] ; KEY = UPDATE_24MAY2010, 1111-1111-1111-1 ; KEY = XXXXX, 2222-2222-2222-2 ; ; The [LICENSE] section may point to an external file which contains ; license keys for one or more PEEDIs. The external file must include ; the text [LICENSE] followed by all keys. ; ; Example: ; [LICENSE] ; FILE = tftp://192.168.3.1/license.txt ; or ; FILE=eep:license.txt ; or ; FILE = ftp://user:password@192.168.3.1/license.txt ; ; ; PEEDI is shipped with license keys stored in "eep:license.txt" and ; printed on a label on the bottom side of PEEDI. ; [LICENSE] FILE=eep:license.txt ;-------------------------------------------------------------------------- [DEBUGGER] PROTOCOL = gdb_remote ; gdb remote REMOTE_PORT = 2000 ; TCP/IP port [TARGET] PLATFORM = ARM ; platform is ARM [PLATFORM_ARM] JTAG_CHAIN = 4 ; list of IR length of all TAP controller in JTAG chain JTAG_CLOCK = 10, 1000 ; JTAG Clock in [kHz] - 10kHz for init operations and ; 1MHz for normal work ;JTAG_CLOCK = 10, ADAPTIVE ; use 10kHz for init operations and then RTCK ;JTAG_CLOCK = ADAPTIVE ; use only RTCK TRST_TYPE = PUSHPULL ; type of TRST output: OPENDRAIN or PUSHPULL RESET_TIME = 20 ; length of RESET pulse in ms; 0 means no RESET WAKEUP_TIME = 20 ; time between releasing the reset and starting the jtag communication CORE0 = ARM7TDMI ; TAP is ARM7TDMI CPU CORE0_STARTUP_MODE = STOP, 100 ; startup mode after reset: ; if RESET than no code is executed after reset ; if STOP,XX then the target executes code for XX period in ms. ; if RUN then the target executes code until stopped by the telnet "halt" command CORE0_BREAKMODE = soft ; default breakpoint mode for the debugger: ; soft - use software breakpoints ; hard - use hardware breakpoints CORE0_INIT = INIT_LPC2138 ; init section for LPC2138 board CORE0_FLASH = FLASH_LPC2138 ; FLASH section parameters CORE0_ENDIAN = LITTLE ; core is little endian CORE0_WORKSPACE_ADDR = 0x40000000 ; address of workspace for programmer CORE0_WORKSPACE_LEN = 0x2000 ; length of workspace in bytes ; Default path to be used if only a file name (without the full path) is ; provided to a PEEDI command or for the FILE parameter in the Flash sections ; Examples: ; In a console: ; "flash prog tftp://192.168.3.1/image.elf" ; is equal to ; "flash prog image.elf" ; ; In a Flash Profile: ; FILE="tftp://192.168.3.1/image.bin", BIN, 0 ; is equal to ; FILE="image.bin", BIN, 0 ; CORE0_PATH = "tftp://192.168.3.60" ;CORE0_PATH = "card://" CORE0_FILE = "myfile.bin", BIN, 0x40000000 ; default file [INIT_LPC2138] memory write 0xE01FC040 0x00000001 ; map FLASH vectors ; Disable PLL for flash programming mem write 0xE01FC080 0x00000000 ;PLLCON: mem write 0xE01FC084 0x00000000 ;PLLCFG: mem write 0xE01FC08C 0x000000AA ;PLLFEED: mem write 0xE01FC08C 0x00000055 ;PLLFEED: wait 20 [FLASH_LPC2138] CHIP = LPC2000 ; flash chip SET_VECTORS_CHECKSUM = YES ; auto set checksum at address 0x14 CPU_CLOCK = 16000 ; CPU clock is 16 MHz FILE = "test32k.bin", BIN, 0 ; file to program AUTO_ERASE = NO ; erase before program [SERIAL] ; serial port configuration BAUD = 115200 STOP_BITS = 1 PARITY = NONE TCP_PORT = 0 ; enable CLI over RS232 ;TCP_PORT = 2023 ; enable serial over TCP/IP [TELNET] PROMPT = "LPC> " ; telnet prompt ;BACKSPACE = 127 ; comment out for autodetect [DISPLAY] BRIGHTNESS = 20 ; LED indicator brightness VOLUME = 25 ; beeper volume [ACTIONS] ; user defined scripts ;AUTORUN = 2 ; executed on every target connect 1 = erase 2 = prog 3 = dump_ram 4 = dump_flash [erase] ; erase flash flash erase [prog] ; program flash flash prog