# README-pre-built_images.ronetix # How to create complete runing system from set of pre-built # bootloader, Linux kernel, root file system. # for AT91SAM9G45/AT91SAM9263/AT91SAM9261 based boards: # PM9G45, PM9263 and PM9261. # # Ronetix GmbH # www.ronetix.at # May, 2011 Table of contents: 1. PM9G45 2. PM9263 3. PM9261 Here are listed a set of pre built images needed to run a Ronetix board. How to program the images take a look at README-porgramming.ronetix. After the images list for each board and kernel version there is a log of the boot process for reference. 1. PM9G45 1.1. PM9G45 v1.3 on BB9G45 AT91Bootsrap: http://download.ronetix.info/boards/linux/bootstrap/nandflashboot/pm9g45-nandflashboot-2.13.bin U-Boot: http://download.ronetix.info/boards/linux/bootloader/u-boot-2010.09/pm9g45_bb9g45_u-boot.bin Linux Kernel: http://download.ronetix.info/boards/linux/kernel/2.6.30/pm9g45_bb9g45_uImage RootFS: http://download.ronetix.info/boards/linux/rootfs/2.6.30-pm9g45/KaeilOS-custom-extra-image-glibc-ipk-2010.1-20110223-ronetix-pm9g45.rootfs.jffs2 -------------------------------------------------------------------------------- Start AT91Bootstrap... -I- Slow clock on internal RC ... switching to external crystal! -I- NAND Flash ID 0xADDA -I- copy from NAND 0x00020000 to RAM 0x73F00000, Size 0x00040000 -I- jump to 0x73F00000 U-Boot 2010.09-00019-g756a35e (Jan 16 2012 - 12:55:52) DRAM: 128 MiB NAND: 256 MiB *** Warning - bad CRC or NAND, using default environment In: serial Out: serial Err: serial Net: No 1-wire device detected! macb0 Hit any key to stop autoboot: 3  2  1  0 NAND read: device 0 offset 0x200000, size 0x200000 2097152 bytes read: OK ## Booting kernel from Legacy Image at 72000000 ... Image Name: Linux-2.6.30 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2000116 Bytes = 1.9 MiB Load Address: 70008000 Entry Point: 70008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux............................................................................................................................. done, booting the kernel. Linux version 2.6.30 (dimov@asenbox) (gcc version 4.4.1 (GCC) ) #325 Tue Aug 21 21:13:03 EEST 2012 CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177 CPU: VIVT data cache, VIVT instruction cache Machine: Ronetix PM9G45 Memory policy: ECC disabled, Data cache writeback Clocks: CPU 400 MHz, master 133 MHz, main 12.000 MHz Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 Kernel command line: fbcon=rotate:0 console=tty0 console=ttyS0,115200 root=/dev/mtdblock4 mtdparts=atmel_nand:128k(bootstrap)ro,256k(uboot)ro,1664k(env),3M(linux)ro,-(root) rw rootfstype=jffs2 Experimental hierarchical RCU implementation. Experimental hierarchical RCU init done. NR_IRQS:192 AT91: 160 gpio irqs in 5 banks PID hash table entries: 512 (order: 9, 2048 bytes) Console: colour dummy device 80x30 console [tty0] enabled console [ttyS0] enabled Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 128MB = 128MB total Memory: 125724KB available (3576K code, 321K data, 120K init, 0K highmem) Calibrating delay loop... 199.47 BogoMIPS (lpj=997376) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok net_namespace: 320 bytes NET: Registered protocol family 16 at91: pm9g45 registering GPIO buttons atmel_tcb: probe of atmel_tcb.0 failed with error -22 bio: create slab at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb cfg80211: Calling CRDA to update world regulatory domain NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered NET: Registered protocol family 1 NetWinder Floating Point Emulator V0.97 (double precision) JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. msgmni has been set to 245 alg: No test for stdrng (krng) io scheduler noop registered io scheduler anticipatory registered (default) atmel_lcdfb atmel_lcdfb.0: 750KiB frame buffer at 77a00000 (mapped at ffa00000) Console: switching to colour frame buffer device 100x30 atmel_lcdfb atmel_lcdfb.0: fb0: Atmel LCDC at 0x00500000 (mapped at c894c000), irq 23 atmel_usart.0: ttyS0 at MMIO 0xfeffee00 (irq = 1) is a ATMEL_SERIAL atmel_usart.1: ttyS1 at MMIO 0xfff8c000 (irq = 7) is a ATMEL_SERIAL atmel_usart.2: ttyS2 at MMIO 0xfff90000 (irq = 8) is a ATMEL_SERIAL atmel_usart.3: ttyS3 at MMIO 0xfff94000 (irq = 9) is a ATMEL_SERIAL atmel_usart.4: ttyS4 at MMIO 0xfff98000 (irq = 10) is a ATMEL_SERIAL loop: module loaded ssc ssc.1: Atmel SSC device at 0xc8970000 (irq 17) Uniform Multi-Platform E-IDE driver ide-gd driver 1.18 Driver 'sd' needs updating - please use bus_type methods MACB_mii_bus: probed Davicom DM9161A: reset PHY chip ... done. eth0: Atmel MACB at 0xfffbc000 irq 25 (00:02:00:00:de:ad) eth0: attached PHY driver [Davicom DM9161A] (mii_bus:phy_addr=ffffffff:00, irq=-1) libertas_sdio: Libertas SDIO driver libertas_sdio: Copyright Pierre Ossman libertas_spi: Libertas SPI driver atmel_nand: nand chip ioremap 0x40000000(Physical) to 0xc9000000(virtual) length 0x10000000 NAND device: Manufacturer ID: 0xad, Chip ID: 0xda (Hynix NAND 256MiB 3,3V 8-bit) AT91 NAND: 8-bit, Software ECC, Sizes: 2048 page, 131072 erase block, 64 oob Scanning device for bad blocks 5 cmdlinepart partitions found on MTD device atmel_nand Creating 5 MTD partitions on "atmel_nand": 0x000000000000-0x000000020000 : "bootstrap" 0x000000020000-0x000000060000 : "uboot" 0x000000060000-0x000000200000 : "env" 0x000000200000-0x000000500000 : "linux" 0x000000500000-0x000010000000 : "root" ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver atmel-ehci atmel-ehci: Atmel EHCI UHP HS atmel-ehci atmel-ehci: new USB bus registered, assigned bus number 1 atmel-ehci atmel-ehci: irq 22, io mem 0x00800000 atmel-ehci atmel-ehci: USB 2.0 started, EHCI 1.00 usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: Atmel EHCI UHP HS usb usb1: Manufacturer: Linux 2.6.30 ehci_hcd usb usb1: SerialNumber: atmel-ehci usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver at91_ohci at91_ohci: AT91 OHCI at91_ohci at91_ohci: new USB bus registered, assigned bus number 2 at91_ohci at91_ohci: irq 22, io mem 0x00700000 usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: AT91 OHCI usb usb2: Manufacturer: Linux 2.6.30 ohci_hcd usb usb2: SerialNumber: at91 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected usbcore: registered new interface driver cdc_acm cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. atmel_usba_udc atmel_usba_udc: MMIO registers at 0xfff78000 mapped at c8956000 atmel_usba_udc atmel_usba_udc: FIFO at 0x00600000 mapped at c8e00000 atmel_usba_udc atmel_usba_udc: Make sure we start from a clean slate: USBa reg. CTRL: 0x200 atmel_usba_udc atmel_usba_udc: Make sure we start from a clean slate: USBa reg. CTRL: 0x200 g_serial gadget: Gadget Serial v2.4 g_serial gadget: g_serial ready mice: PS/2 mouse device common for all mice input: gpio-keys as /class/input/input0 atmel_tsadcc atmel_tsadcc: mapped at c8980000. atmel_tsadcc atmel_tsadcc: Master clock is set at: 133333333 Hz atmel_tsadcc atmel_tsadcc: Prescaler is set at: 165 input: atmel touch screen controller as /class/input/input1 rtc-at91sam9 at91_rtt.0: rtc core: registered at91_rtt as rtc0 IRQ 1/rtc0: IRQF_DISABLED is not guaranteed on shared IRQs rtc-at91sam9 at91_rtt.0: rtc0: SET TIME! i2c /dev entries driver i2c-gpio i2c-gpio.0: using pins 52 (SDA) and 53 (SCL) Driver for 1-wire Dallas network protocol. Registered led device: led0 Registered led device: led1 at_hdmac at_hdmac: Atmel AHB DMA Controller ( cpy slave ), 8 channels usbcore: registered new interface driver usbhid usbhid: v2.6:USB HID core driver Advanced Linux Sound Architecture Driver Version 1.0.20. No device for DAI atmel-ssc0 No device for DAI atmel-ssc1 asoc: WM8731 <-> atmel-ssc0 mapping ok ALSA device list: #0: AT91SAMG20-EK (WM8731) TCP cubic registered NET: Registered protocol family 17 RPC: Registered udp transport module. RPC: Registered tcp transport module. lib80211: common routines for IEEE802.11 drivers rtc-at91sam9 at91_rtt.0: hctosys: unable to read the hardware clock atmel_mci atmel_mci.0: Using dma0chan0 for DMA transfers atmel_mci atmel_mci.0: Atmel MCI controller at 0xfff80000 irq 11, 1 slots VFS: Mounted root (jffs2 filesystem) on device 31:4. Freeing init memory: 120K mmc0: new SD card at address 1234 mmcblk0: mmc0:1234 SA02G 1.83 GiB (ro) mmcblk0: p1 INIT: version 2.86 booting Please wait: booting... Starting udev udevd-work[519]: error opening ATTR{/sys/class/sound/controlC0/../uevent} for writing: No such file or directory Remounting root file system... Caching udev devnodes Populating dev cache ALSA: Restoring mixer settings... Cleaning: /etc/network/run/ifstate. Configuring network interfaces... eth0 no wireless extensions. Internet Systems Consortium DHCP Client 4.1.1-P1 Copyright 2004-2010 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/00:02:00:00:de:ad Sending on LPF/eth0/00:02:00:00:de:ad Sending on Socket/fallback eth0: link up (100/Full) DHCPREQUEST on eth0 to 255.255.255.255 port 67 DHCPACK from 192.168.10.1 bound to 192.168.10.105 -- renewal in 6283 seconds. done. Starting portmap daemon: portmap. net.ipv4.conf.default.rp_filter = 1 net.ipv4.conf.all.rp_filter = 1 hwclock: RTC_RD_TIME: Invalid or incomplete multibyte or wide character INIT: Entering runlevel: 5 Starting system message bus: dbus. Starting Hardware abstraction layer hald Starting Dropbear SSH server: dropbear. Starting Network Interface Plugging Daemon: eth0. creating NFS state directory: done starting 8 nfsd kernel threads: done starting mountd: done starting statd: done Starting syslogd/klogd: done * Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon ...done. Starting Bluetooth subsystem: bluetoothd. Starting Network connection manager daemon: NetworkManager. Starting GPE display manager: gpe-dm _ __ _ _ | |/ /__ _ ___(_) | ___ ___ | ' // _` |/ _ ' | |/ _ '/ __| | . ' (_| | __/ | | (_) __ '. |_|'_'_ ,_|'___|_|_|'___/|___/(R) KaeilOS Linux ronetix-pm9g45 ttyS0 KaeilOS 2010.1-20110103 ronetix-pm9g45 ttyS0 ronetix-pm9g45 login: root root@ronetix-pm9g45:~# -------------------------------------------------------------------------------- 1.1. PM9G45 v1.3 on BB9263 AT91Bootsrap: http://download.ronetix.info/boards/linux/bootstrap/nandflashboot/pm9g45-nandflashboot-2.13.bin U-Boot: http://download.ronetix.info/boards/linux/bootloader/u-boot-2010.09/pm9g45_bb9263_u-boot.bin Linux Kernel: http://download.ronetix.info/boards/linux/kernel/2.6.30/pm9g45_bb9263_uImage RootFS: http://download.ronetix.info/boards/linux/rootfs/2.6.30-pm9g45/KaeilOS-custom-extra-image-glibc-ipk-2010.1-20110223-ronetix-pm9g45-bb9263.rootfs.jffs2 -------------------------------------------------------------------------------- Start AT91Bootstrap... -I- Slow clock on internal RC ... switching to external crystal! -I- NAND Flash ID 0xADDA -I- copy from NAND 0x00020000 to RAM 0x73F00000, Size 0x00040000 -I- jump to 0x73F00000 U-Boot 2010.09-00019-g756a35e (Jan 16 2012 - 13:00:11) DRAM: 128 MiB NAND: 256 MiB *** Warning - bad CRC or NAND, using default environment In: serial Out: serial Err: serial Net: No 1-wire device detected! macb0 macb0: PHY present at 0 macb0: Starting autonegotiation... macb0: Autonegotiation complete macb0: link up, 100Mbps full-duplex (lpa: 0xcde1) Hit any key to stop autoboot: 3  2  1  0 NAND read: device 0 offset 0x200000, size 0x200000 2097152 bytes read: OK ## Booting kernel from Legacy Image at 72000000 ... Image Name: Linux-2.6.30 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1898052 Bytes = 1.8 MiB Load Address: 70008000 Entry Point: 70008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux....................................................................................................................... done, booting the kernel. Linux version 2.6.30 (dimov@asenbox) (gcc version 4.4.1 (GCC) ) #326 Tue Aug 21 21:33:28 EEST 2012 CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177 CPU: VIVT data cache, VIVT instruction cache Machine: Ronetix PM9G45 Memory policy: ECC disabled, Data cache writeback Clocks: CPU 400 MHz, master 133 MHz, main 12.000 MHz Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 Kernel command line: fbcon=rotate:3 console=tty0 console=ttyS0,115200 root=/dev/mtdblock4 mtdparts=atmel_nand:128k(bootstrap)ro,256k(uboot)ro,1664k(env),3M(linux)ro,-(root) rw rootfstype=jffs2 Experimental hierarchical RCU implementation. Experimental hierarchical RCU init done. NR_IRQS:192 AT91: 160 gpio irqs in 5 banks PID hash table entries: 512 (order: 9, 2048 bytes) Console: colour dummy device 80x30 console [tty0] enabled console [ttyS0] enabled Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 128MB = 128MB total Memory: 125908KB available (3396K code, 319K data, 116K init, 0K highmem) Calibrating delay loop... 199.47 BogoMIPS (lpj=997376) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok net_namespace: 320 bytes NET: Registered protocol family 16 at91: pm9g45 registering GPIO buttons atmel_tcb: probe of atmel_tcb.0 failed with error -22 bio: create slab at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered NET: Registered protocol family 1 NetWinder Floating Point Emulator V0.97 (double precision) JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. msgmni has been set to 246 alg: No test for stdrng (krng) io scheduler noop registered io scheduler anticipatory registered (default) atmel_lcdfb atmel_lcdfb.0: 150KiB frame buffer at 779c0000 (mapped at ffa00000) Console: switching to colour frame buffer device 40x15 atmel_lcdfb atmel_lcdfb.0: fb0: Atmel LCDC at 0x00500000 (mapped at c894c000), irq 23 atmel_usart.0: ttyS0 at MMIO 0xfeffee00 (irq = 1) is a ATMEL_SERIAL atmel_usart.1: ttyS1 at MMIO 0xfff8c000 (irq = 7) is a ATMEL_SERIAL atmel_usart.2: ttyS2 at MMIO 0xfff90000 (irq = 8) is a ATMEL_SERIAL atmel_usart.3: ttyS3 at MMIO 0xfff94000 (irq = 9) is a ATMEL_SERIAL atmel_usart.4: ttyS4 at MMIO 0xfff98000 (irq = 10) is a ATMEL_SERIAL loop: module loaded Uniform Multi-Platform E-IDE driver ide-gd driver 1.18 Driver 'sd' needs updating - please use bus_type methods MACB_mii_bus: probed Davicom DM9161A: reset PHY chip ... done. eth0: Atmel MACB at 0xfffbc000 irq 25 (00:02:00:00:de:ad) eth0: attached PHY driver [Davicom DM9161A] (mii_bus:phy_addr=ffffffff:00, irq=-1) libertas_sdio: Libertas SDIO driver libertas_sdio: Copyright Pierre Ossman libertas_spi: Libertas SPI driver atmel_nand: nand chip ioremap 0x40000000(Physical) to 0xc9000000(virtual) length 0x10000000 NAND device: Manufacturer ID: 0xad, Chip ID: 0xda (Hynix NAND 256MiB 3,3V 8-bit) AT91 NAND: 8-bit, Software ECC, Sizes: 2048 page, 131072 erase block, 64 oob Scanning device for bad blocks 5 cmdlinepart partitions found on MTD device atmel_nand Creating 5 MTD partitions on "atmel_nand": 0x000000000000-0x000000020000 : "bootstrap" 0x000000020000-0x000000060000 : "uboot" 0x000000060000-0x000000200000 : "env" 0x000000200000-0x000000500000 : "linux" 0x000000500000-0x000010000000 : "root" atmel_spi atmel_spi.0: Atmel SPI Controller at 0xfffa4000 (irq 14) atmel_spi atmel_spi.1: Atmel SPI Controller at 0xfffa8000 (irq 15) at91_cf: irqs det #141, io #161 ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver atmel-ehci atmel-ehci: Atmel EHCI UHP HS atmel-ehci atmel-ehci: new USB bus registered, assigned bus number 1 atmel-ehci atmel-ehci: irq 22, io mem 0x00800000 atmel-ehci atmel-ehci: USB 2.0 started, EHCI 1.00 usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: Atmel EHCI UHP HS usb usb1: Manufacturer: Linux 2.6.30 ehci_hcd usb usb1: SerialNumber: atmel-ehci usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver at91_ohci at91_ohci: AT91 OHCI at91_ohci at91_ohci: new USB bus registered, assigned bus number 2 at91_ohci at91_ohci: irq 22, io mem 0x00700000 usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: AT91 OHCI usb usb2: Manufacturer: Linux 2.6.30 ohci_hcd usb usb2: SerialNumber: at91 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected usbcore: registered new interface driver cdc_acm cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. mice: PS/2 mouse device common for all mice input: gpio-keys as /class/input/input0 setting trigger mode 2 for irq 146 failed (gpio_irq_type+0x0/0x18) ads7846 spi1.0: trying pin change workaround on irq 146 ads7846 spi1.0: external vREF for ADS7843 not specified ads7846 spi1.0: touchscreen, irq 146 input: ADS7843 Touchscreen as /class/input/input1 rtc-at91sam9 at91_rtt.0: rtc core: registered at91_rtt as rtc0 IRQ 1/rtc0: IRQF_DISABLED is not guaranteed on shared IRQs rtc-at91sam9 at91_rtt.0: rtc0: SET TIME! i2c /dev entries driver Driver for 1-wire Dallas network protocol. Registered led device: led0 Registered led device: led1 at_hdmac at_hdmac: Atmel AHB DMA Controller ( cpy slave ), 8 channels usbcore: registered new interface driver usbhid usbhid: v2.6:USB HID core driver Advanced Linux Sound Architecture Driver Version 1.0.20. atmel_ac97c atmel_ac97c.0: Atmel AC97 controller at 0xc8988000, irq = 24 ALSA device list: #0: Atmel AC97 controller TCP cubic registered NET: Registered protocol family 17 RPC: Registered udp transport module. RPC: Registered tcp transport module. lib80211: common routines for IEEE802.11 drivers rtc-at91sam9 at91_rtt.0: hctosys: unable to read the hardware clock atmel_mci atmel_mci.0: Using dma0chan0 for DMA transfers atmel_mci atmel_mci.0: Atmel MCI controller at 0xfff80000 irq 11, 1 slots VFS: Mounted root (jffs2 filesystem) on device 31:4. Freeing init memory: 116K INIT: version 2.86 booting Please wait: booting... Starting udev udevd-work[513]: error opening ATTR{/sys/class/sound/controlC0/../uevent} for writing: No such file or directory Remounting root file system... Caching udev devnodes Populating dev cache Undefined users: Skipping /etc/default/volatiles/99_hal ALSA: Restoring mixer settings... Configuring network interfaces... No state is present for card AC97C Unknown hardware: "Atmel AC97C" "Analog Devices AD1981B" "AC97a:41445374" "" "" Hardware is initialized using a guess method No state is present for card AC97C eth0 no wireless extensions. Internet Systems Consortium DHCP Client 4.1.1-P1 Copyright 2004-2010 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/00:02:00:00:de:ad Sending on LPF/eth0/00:02:00:00:de:ad Sending on Socket/fallback DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 4 eth0: link up (100/Full) DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 7 DHCPOFFER from 192.168.10.1 DHCPREQUEST on eth0 to 255.255.255.255 port 67 DHCPACK from 192.168.10.1 bound to 192.168.10.105 -- renewal in 5512 seconds. done. Starting portmap daemon: portmap. net.ipv4.conf.default.rp_filter = 1 net.ipv4.conf.all.rp_filter = 1 hwclock: RTC_RD_TIME: Invalid or incomplete multibyte or wide character Checking for built-in Bluetooth: no Configuring hicolor-icon-theme. Configuring pango-module-basic-x. Configuring pango-module-basic-fc. Configuring ttf-dejavu-common. Configuring ttf-dejavu-sans. Configuring gdk-pixbuf-loader-png. Configuring gdk-pixbuf-loader-jpeg. Configuring gdk-pixbuf-loader-gif. Configuring gdk-pixbuf-loader-xpm. Configuring dbus. Adding system startup for /etc/init.d/dbus-1. Configuring policykit. Configuring ntpdate. adding crontab Configuring update-modules. Configuring ttf-dejavu-sans-mono. Configuring hal. Cannot create link over existing -/etc/resolv.conf-. Configuring libnss-mdns. Configuring avahi-daemon. Adding system startup for /etc/init.d/avahi-daemon. Configuring avahi-autoipd. Configuring networkmanager. Cannot create link over existing -/etc/resolv.conf-. Adding system startup for /etc/init.d/NetworkManager. INIT: Entering runlevel: 5 Starting system message bus: dbus. Starting Hardware abstraction layer hald Creating Dropbear SSH server RSA host key. Will output 1024 bit rsa secret key to '/etc/dropbear/dropbear_rsa_host_key' Generating key, this may take a while... Public key portion is: ssh-rsa AAAAB3NzaC1yc2EAAAADAQABAAAAgwCwCWpsW/b3XrB1WULIpVT50cJSLcMhZ5+YxoZkJZu7qDM9Y/dRmtRqIb/4259W59C2JbNIgVa6oz0gZGVOPVpG/dzqigfmcfRI4FXgZywRxrMJ3s3idDOrpQVV5RzcfymiPmCPznOVuWHJdz6wfIltlrtRSO4MH4ta7/buHqG84/WV root@ronetix-pm9g45 Fingerprint: md5 6e:74:51:c4:58:2c:67:91:5b:61:9a:55:23:12:10:33 Starting Dropbear SSH server: dropbear. Starting Network Interface Plugging Daemon: eth0. creating NFS state directory: done starting 8 nfsd kernel threads: done starting mountd: done starting statd: done Starting syslogd/klogd: done * Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon ...done. Starting Bluetooth subsystem: bluetoothd. Starting Network connection manager daemon: NetworkManager. Starting GPE display manager: gpe-dm _ __ _ _ | |/ /__ _ ___(_) | ___ ___ | ' // _` |/ _ ' | |/ _ '/ __| | . ' (_| | __/ | | (_) __ '. |_|'_'_ ,_|'___|_|_|'___/|___/(R) KaeilOS Linux ronetix-pm9g45 ttyS0 KaeilOS 2010.1-20110103 ronetix-pm9g45 ttyS0 ronetix-pm9g45 login: root root@ronetix-pm9g45:~# -------------------------------------------------------------------------------- 2. PM9263 U-Boot: http://download.ronetix.info/boards/linux/bootloader/u-boot-2010.09/pm9263_u-boot.bin Linux Kernel: http://download.ronetix.info/boards/linux/kernel/2.6.28/uImage-2.6.28-r12-ronetix-pm9263.bin RootFS: http://download.ronetix.info/boards/linux/rootfs/2.6.28-pm9263/KaeilOS-console-image-glibc-ipk-2009.1-test-20090909-ronetix-pm9263.rootfs.jffs2 or http://download.ronetix.info/boards/linux/rootfs/2.6.28-pm9263/KaeilOS-custom-extra-image-glibc-ipk-2009.1-test-20090916-ronetix-pm9263.rootfs.jffs2 -------------------------------------------------------------------------------- U-Boot 2010.09-00014-g76b3a68 (Jun 24 2011 - 15:48:14) CPU: AT91SAM9263 Crystal frequency: 18.432 MHz CPU clock : 199.680 MHz Master clock : 99.840 MHz Board : Ronetix PM9263 Video memory : 0x70000000 (PSRAM) DRAM: 64 MiB Flash: 4 MiB NAND: 256 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: Setting environment variable 'ethaddr' to 02:00:00:EB:41:29 macb0 Hit any key to stop autoboot: 3  2  1  0 ## Booting kernel from Legacy Image at 10050000 ... Image Name: KaeilOS/2.6.28/ronetix-pm9263 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1601372 Bytes = 1.5 MiB Load Address: 20008000 Entry Point: 20008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux........................................................................................................ done, booting the kernel. Linux version 2.6.28 (dimov@tserv) (gcc version 4.2.4) #5 Wed Sep 16 21:37:36 EEST 2009 CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177 CPU: VIVT data cache, VIVT instruction cache Machine: Ronetix PM9263 Memory policy: ECC disabled, Data cache writeback Clocks: CPU 199 MHz, master 99 MHz, main 18.432 MHz Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 Kernel command line: root=/dev/mtdblock4 rootfstype=jffs2 fbcon=rotate:3 mtdparts=physmap-flash.0:256k(u-boot)ro,64k(u-boot-env)ro,1408k(kernel),-(rootfs);nand:-(nand) f AT91: 160 gpio irqs in 5 banks PID hash table entries: 256 (order: 8, 1024 bytes) Console: colour dummy device 80x30 console [tty0] enabled console [ttyS0] enabled Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Memory: 64MB = 64MB total Memory: 61504KB available (2968K code, 248K data, 132K init) Calibrating delay loop... 99.53 BogoMIPS (lpj=497664) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok net_namespace: 288 bytes NET: Registered protocol family 16 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 2048 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 1, 8192 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP reno registered NET: Registered protocol family 1 JFFS2 version 2.2. (NAND) �© 2001-2006 Red Hat, Inc. msgmni has been set to 120 io scheduler noop registered io scheduler anticipatory registered (default) atmel_lcdfb atmel_lcdfb.0: backlight control is not available atmel_lcdfb atmel_lcdfb.0: 4096KiB frame buffer at 70000000 (mapped at c5000000) Console: switching to colour frame buffer device 40x30 atmel_lcdfb atmel_lcdfb.0: fb0: Atmel LCDC at 0x00700000 (mapped at c4866000), irq 26 atmel_usart.0: ttyS0 at MMIO 0xfeffee00 (irq = 1) is a ATMEL_SERIAL atmel_usart.1: ttyS1 at MMIO 0xfff8c000 (irq = 7) is a ATMEL_SERIAL brd: module loaded loop: module loaded MACB_mii_bus: probed eth0: Atmel MACB at 0xfffbc000 irq 21 (02:00:00:e1:22:3f) eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=ffffffff:01, irq=-1) Uniform Multi-Platform E-IDE driver ide-gd driver 1.18 Driver 'sd' needs updating - please use bus_type methods Driver 'sr' needs updating - please use bus_type methods physmap platform flash device: 00400000 at 10000000 physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank Amd/Fujitsu Extended Query Table at 0x0040 number of CFI chips: 1 cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. 4 cmdlinepart partitions found on MTD device physmap-flash.0 Creating 4 MTD partitions on "physmap-flash.0": 0x00000000-0x00040000 : "u-boot" 0x00040000-0x00050000 : "u-boot-env" 0x00050000-0x001b0000 : "kernel" 0x001b0000-0x00400000 : "rootfs" NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron NAND 256MiB 3,3V 8-bit) AT91 NAND: 8-bit, Software ECC Scanning device for bad blocks Bad eraseblock 479 at 0x03be0000 Bad eraseblock 489 at 0x03d20000 Bad eraseblock 1300 at 0x0a280000 Bad eraseblock 1869 at 0x0e9a0000 Creating 1 MTD partitions on "atmel_nand": 0x00000000-0x10000000 : "Partition 1" atmel_spi atmel_spi.0: Atmel SPI Controller at 0xfffa4000 (irq 14) atmel_spi atmel_spi.1: Atmel SPI Controller at 0xfffa8000 (irq 15) at91_cf: irqs det #62, io #56 usbmon: debugfs is not available ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver at91_ohci at91_ohci: AT91 OHCI at91_ohci at91_ohci: new USB bus registered, assigned bus number 1 at91_ohci at91_ohci: irq 29, io mem 0x00a00000 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver libusual udc: at91_udc version 3 May 2006 mice: PS/2 mouse device common for all mice ads7846 spi1.0: touchscreen, irq 31 input: ADS784x Touchscreen as /devices/platform/atmel_spi.1/spi1.0/input/input0 rtc-at91sam9 at91_rtt.0: rtc core: registered at91_rtt as rtc0 rtc-at91sam9 at91_rtt.0: rtc0: SET TIME! Driver for 1-wire Dallas network protocol. Registered led device: led0 Registered led device: led1 usbcore: registered new interface driver usbhid usbhid: v2.6:USB HID core driver Advanced Linux Sound Architecture Driver Version 1.0.18rc3. AC97C regs = FFFA0000 AC97C irq = 18 at91-ac97: codec write timeout <4>at91-ac97: codec write timeout <4>at91-ac97: codec write timeout <4>at91-ac97: codec write timeout <6>ALSA device list: #0: Atmel AC97 Controller at 0xfffa0000, irq 18 TCP cubic registered NET: Registered protocol family 17 RPC: Registered udp transport module. RPC: Registered tcp transport module. rtc-at91sam9 at91_rtt.0: hctosys: unable to read the hardware clock VFS: Mounted root (jffs2 filesystem). Freeing init memory: 132K INIT: version 2.86 booting -------------------------------------------------------------------------------- 3. PM9261 A. for Linux Kernel 2.6.25 U-Boot: http://download.ronetix.info/boards/linux/bootloader/u-boot-2010.06/pm9261_u-boot.bin Linux Kernel: http://download.ronetix.info/boards/linux/kernel/2.6.25/uImage-2.6.25.20-r2-ronetix-pm9261.bin RootFS: http://download.ronetix.info/boards/linux/rootfs/2.6.25.20-pm9261/KaeilOS-console-image-glibc-ipk-2009.1-test-20090813-ronetix-pm9261.rootfs.jffs2 or http://download.ronetix.info/boards/linux/rootfs/2.6.25.20-pm9261/KaeilOS-custom-extra-image-glibc-ipk-2009.1-test-20090916-ronetix-pm9261.rootfs.jffs2 -------------------------------------------------------------------------------- U-Boot 2010.06-00697-g09506a9 (Sep 03 2010 - 19:55:28) Board : Ronetix PM9261 Crystal frequency: 18.432 MHz CPU clock : 199.066 MHz Master clock : 99.533 MHz DRAM: 64 MiB Flash: 4 MiB NAND: 256 MiB DataFlash:AT45DB321 Nb pages: 8192 Page Size: 528 Size= 4325376 bytes Logical address: 0xC0000000 Area 0: C0000000 to C041FFFF *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: dm9000 Setting environment variable 'ethaddr' to 02:00:00:4A:6A:7 dm9000 i/o: 0x30000000, id: 0x90000a46 DM9000: running in 16 bit mode MAC: 02:00:00:4a:6a:07 operating at 100M full duplex mode Hit any key to stop autoboot: 0 ## Booting kernel from Legacy Image at 10050000 ... Image Name: KaeilOS/2.6.25.20/ronetix-pm9261 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1519312 Bytes = 1.4 MiB Load Address: 20008000 Entry Point: 20008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux.................................................................................................. done, booting the kernel. Linux version 2.6.25.20 (dimov@tserv) (gcc version 4.2.4) #1 Thu Sep 10 11:08:52 EEST 2009 CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177 Machine: Ronetix PM9261 Memory policy: ECC disabled, Data cache writeback Clocks: CPU 199 MHz, master 99 MHz, main 18.432 MHz CPU0: D VIVT write-back cache CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 Kernel command line: root=/dev/mtdblock4 rootfstype=jffs2 fbcon=rotate:3 mtdparts=physmap-flash.0:256k(u-boot)ro,64k(u-boot-env)ro,1408k(kernel),-(rootfs);nand:-(nand) f AT91: 96 gpio irqs in 3 banks PID hash table entries: 256 (order: 8, 1024 bytes) Console: colour dummy device 80x30 console [tty0] enabled console [ttyS0] enabled Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Memory: 64MB = 64MB total Memory: 61696KB available (2808K code, 254K data, 120K init) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok net_namespace: 152 bytes NET: Registered protocol family 16 usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 2048 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 1, 8192 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP reno registered JFFS2 version 2.2. (NAND) �© 2001-2006 Red Hat, Inc. io scheduler noop registered io scheduler anticipatory registered (default) atmel_lcdfb atmel_lcdfb.0: backlight control is not available atmel_lcdfb atmel_lcdfb.0: 150KiB frame buffer at 23d00000 (mapped at ffc00000) Console: switching to colour frame buffer device 40x30 atmel_lcdfb atmel_lcdfb.0: fb0: Atmel LCDC at 0x00600000 (mapped at c4850000), irq 21 atmel_usart.0: ttyS0 at MMIO 0xfefff200 (irq = 1) is a ATMEL_SERIAL atmel_usart.1: ttyS1 at MMIO 0xfffb0000 (irq = 6) is a ATMEL_SERIAL brd: module loaded loop: module loaded dm9000 Ethernet Driver, V1.30 eth0: dm9000 at c4852000,c4854004 IRQ 56 MAC: 02:00:00:4a:6a:07 (chip) Uniform Multi-Platform E-IDE driver ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx physmap platform flash device: 00400000 at 10000000 physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank Amd/Fujitsu Extended Query Table at 0x0040 number of CFI chips: 1 cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. 4 cmdlinepart partitions found on MTD device physmap-flash.0 Creating 4 MTD partitions on "physmap-flash.0": 0x00000000-0x00040000 : "u-boot" 0x00040000-0x00050000 : "u-boot-env" 0x00050000-0x001b0000 : "kernel" 0x001b0000-0x00400000 : "rootfs" NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron NAND 256MiB 3,3V 8-bit) AT91 NAND: 8-bit, Software ECC Scanning device for bad blocks Creating 1 MTD partitions on "at91_nand": 0x00000000-0x10000000 : "nand" atmel_spi atmel_spi.0: Atmel SPI Controller at 0xfffc8000 (irq 12) mtd_dataflash spi0.0: AT45DB321x (4224 KBytes) pm9261_tsc2301_spi spi0.2: touchscreen, irq 93 input: TSC2301 Touchscreen as /devices/platform/atmel_spi.0/spi0.2/input/input0 at91_cf: irqs det #55, io #57 usbmon: debugfs is not available at91_ohci at91_ohci: AT91 OHCI at91_ohci at91_ohci: new USB bus registered, assigned bus number 1 at91_ohci at91_ohci: irq 20, io mem 0x00500000 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected mice: PS/2 mouse device common for all mice input: gpio-keys as /devices/platform/gpio-keys/input/input1 rtc-at91sam9 at91_rtt.0: rtc core: registered at91_rtt as rtc0 rtc-at91sam9 at91_rtt.0: rtc0: SET TIME! Driver for 1-wire Dallas network protocol. at91sam9_wdt: invalid timeout (must be between 1 and 16) mmc_spi spi0.3: can't share SPI bus mmc_spi: probe of spi0.3 failed with error -16 Registered led device: led0 Registered led device: led1 Registered led device: led2 usbcore: registered new interface driver usbhid drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver Advanced Linux Sound Architecture Driver Version 1.0.16rc2 (Thu Jan 31 16:40:16 2008 UTC). ASoC version 0.13.2 check spi driver tsc2301: TSC2301 Audio Codec 0.2 tsc2301: tsc2301_probe: spi=c3d98800 asoc: TSC2301 <-> at91-ssc1 mapping ok ALSA device list: #0: PM9261 (TSC2301) TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 RPC: Registered udp transport module. RPC: Registered tcp transport module. rtc-at91sam9 at91_rtt.0: hctosys: unable to read the hardware clock VFS: Mounted root (jffs2 filesystem). Freeing init memory: 120K INIT: version 2.86 booting -------------------------------------------------------------------------------- B. for Linux Kernel 2.6.23.14 U-Boot: http://download.ronetix.info/boards/linux/bootloader/u-boot-2010.06/pm9261_u-boot.bin Linux Kernel: http://download.ronetix.info/boards/linux/kernel/2.6.23/uImage-2.6.23.14-pm9261 RootFS: http://download.ronetix.info/boards/linux/rootfs/2.6.23.14-pm9261/rootfs-pm926x-openzaurus.jffs2 -------------------------------------------------------------------------------- U-Boot 2010.06-00697-g09506a9 (Sep 03 2010 - 19:55:28) Board : Ronetix PM9261 Crystal frequency: 18.432 MHz CPU clock : 199.066 MHz Master clock : 99.533 MHz DRAM: 64 MiB Flash: 4 MiB NAND: 256 MiB DataFlash:AT45DB321 Nb pages: 8192 Page Size: 528 Size= 4325376 bytes Logical address: 0xC0000000 Area 0: C0000000 to C041FFFF *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: dm9000 Setting environment variable 'ethaddr' to 02:00:00:4A:6A:7 dm9000 i/o: 0x30000000, id: 0x90000a46 DM9000: running in 16 bit mode MAC: 02:00:00:4a:6a:07 operating at 100M full duplex mode Hit any key to stop autoboot: 0 ## Booting kernel from Legacy Image at 10050000 ... Image Name: Linux-2.6.23.14-pm9261 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1514524 Bytes = 1.4 MiB Load Address: 20008000 Entry Point: 20008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux................................................................................................... done, booting the kernel. Linux version 2.6.23.14-pm9261 (support@ronetix.at) (gcc version 4.1.1) #1 Wed May 7 12:18:48 CEST 2008 CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177 Machine: Ronetix PM9261/BB9261 Memory policy: ECC disabled, Data cache writeback Clocks: CPU 199 MHz, master 99 MHz, main 18.432 MHz CPU0: D VIVT write-back cache CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets Built 1 zonelists in Zone order. Total pages: 16256 Kernel command line: root=/dev/mtdblock4 rootfstype=jffs2 fbcon=rotate:3 mtdparts=physmap-flash.0:256k(u-boot)ro,64k(u-boot-env)ro,1408k(kernel),-(rootfs);nand:-(nand) f AT91: 96 gpio irqs in 3 banks PID hash table entries: 256 (order: 8, 1024 bytes) Console: colour dummy device 80x30 console [tty0] enabled console [ttyS0] enabled Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Memory: 64MB = 64MB total Memory: 61696KB available (2828K code, 232K data, 104K init) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok NET: Registered protocol family 16 Generic PHY: Registered new driver usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 2048 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 1, 8192 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP reno registered NetWinder Floating Point Emulator V0.97 (double precision) JFFS2 version 2.2. (NAND) �© 2001-2006 Red Hat, Inc. io scheduler noop registered io scheduler anticipatory registered (default) atmel_lcdfb atmel_lcdfb.0: 150KiB frame buffer at 23cc0000 (mapped at ffc00000) Console: switching to colour frame buffer device 40x30 atmel_lcdfb atmel_lcdfb.0: fb0: Atmel LCDC at 0x00600000 (mapped at c4850000), irq 21 atmel_usart.0: ttyS0 at MMIO 0xfefff200 (irq = 1) is a ATMEL_SERIAL atmel_usart.1: ttyS1 at MMIO 0xfffb0000 (irq = 6) is a ATMEL_SERIAL dm9000 Ethernet Driver eth0: dm9000 at c4852000,c4854004 IRQ 56 MAC: 02:00:00:4a:6a:07 Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx physmap platform flash device: 04000000 at 10000000 physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank Amd/Fujitsu Extended Query Table at 0x0040 number of CFI chips: 1 cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. 4 cmdlinepart partitions found on MTD device physmap-flash.0 Creating 4 MTD partitions on "physmap-flash.0": 0x00000000-0x00040000 : "u-boot" 0x00040000-0x00050000 : "u-boot-env" 0x00050000-0x001b0000 : "kernel" 0x001b0000-0x00400000 : "rootfs" NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron NAND 256MiB 3,3V 8-bit) Scanning device for bad blocks Creating 1 MTD partitions on "NAND 256MiB 3,3V 8-bit": 0x00000000-0x10000000 : "nand" atmel_spi atmel_spi.0: Atmel SPI Controller at 0xfffc8000 (irq 12) mtd_dataflash spi0.0: AT45DB321x (4224 KBytes) pm9261_tsc2301_spi spi0.2: touchscreen, irq 93 input: TSC2301 Touchscreen as /class/input/input0 at91_cf: irqs det #55, io #57 at91_ohci at91_ohci: AT91 OHCI at91_ohci at91_ohci: new USB bus registered, assigned bus number 1 at91_ohci at91_ohci: irq 20, io mem 0x00500000 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected mice: PS/2 mouse device common for all mice at91_rtc at91_rtc: rtc core: registered at91_rtc as rtc0 AT91SAM9 Real Time Clock driver. Driver for 1-wire Dallas network protocol. pm926x_w1, gpio pin 39 Registered led device: led0 Registered led device: led1 Registered led device: led2 usbcore: registered new interface driver usbhid drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver Advanced Linux Sound Architecture Driver Version 1.0.14 (Fri Jul 20 09:12:58 2007 UTC). ASoC version 0.13.1 check spi driver tsc2301: TSC2301 Audio Codec 0.2 tsc2301: tsc2301_probe: spi=c3d4d200 asoc: TSC2301 <-> at91-ssc1 mapping ok ALSA device list: #0: PM9261 (TSC2301) TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 at91_rtc at91_rtc: setting the system clock to 1970-01-01 00:00:09 (9) eth0: link up, 100Mbps, full-duplex, lpa 0xCDE1 Sending BOOTP requests . OK IP-Config: Got BOOTP answer from 0.0.0.0, my address is 192.168.10.227 IP-Config: Complete: device=eth0, addr=192.168.10.227, mask=255.255.255.0, gw=192.168.10.1, host=192.168.10.227, domain=ronetix.at, nis-domain=ronetix.at, bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= Empty flash at 0x00545878 ends at 0x00546000 VFS: Mounted root (jffs2 filesystem). Freeing init memory: 104K -------------------------------------------------------------------------------- Note: Unique file identification The name of the files should be descriptive and easy to remember and use. Sometimes their names are not enough to distinguish files, so file SHA256 message digest(check sum) will be used to identify them, in some cases the UUID(universally unique identifier) could be used. Check md5sum.txt and sha256sum.txt.