AT91Bootstrap 3.8.1-00004-g53c63f9 (Mit Feb 24 15:39:51 CET 2016) 1-Wire: Loading 1-Wire information ... 1-Wire: ROM Searching ... Done, 0x2 1-Wire chips found 1-Wire: BoardName | [Revid] | VendorName #0x0 SAMA5D33-CM [B2] RONETIX #0x1 SAMA5D3x-MB [CC3] FLEX 1-Wire: Failed to read DM board information 1-Wire: SYS_GPBR2: 0x480006b, SYS_GPBR3: 0x610801 MEMTEST: start 0x26f00000, length 0x80000 ... done NAND: ONFI flash detected NAND: Manufacturer ID: 0x2c Chip ID: 0x32 NAND: Page Bytes: 0x800, Spare Bytes: 0x40 NAND: ECC Correctability Bits: 0x4, ECC Sector Bytes: 0x200 NAND: Disable On-Die ECC NAND: Initialize PMECC params, cap: 0x8, sector: 0x200 NAND: Image: Copy 0x80000 bytes from 0x40000 to 0x26f00000 NAND: CRC32 checksum OK NAND: Done to load image U-Boot 2017.03-linux4sam_5.8-00003-gfb21c1f61e (Jun 06 2018 - 15:49:58 +0200) CPU: SAMA5D33 Crystal frequency: 12 MHz CPU clock : 528 MHz Master clock : 132 MHz DRAM: 512 MiB Flash: 16 MiB NAND: 256 MiB MMC: Atmel mci: 0, Atmel mci: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: Error: ethernet@f0028000 address not set. No ethernet found. Hit any key to stop autoboot: 0 NAND read: device 0 offset 0x300000, size 0x600000 6291456 bytes read: OK ## Loading kernel from FIT Image at 22000000 ... Using 'conf@sama5d33ek' configuration Trying 'kernel@1' kernel subimage Description: AT91 SAMA5D3 Linux kernel Type: Kernel Image Compression: uncompressed Data Start: 0x220000f0 Data Size: 3753552 Bytes = 3.6 MiB Architecture: ARM OS: Linux Load Address: 0x20008000 Entry Point: 0x20008000 Hash algo: crc32 Hash value: c6d84660 Verifying Hash Integrity ... crc32+ OK ## Loading fdt from FIT Image at 22000000 ... Using 'conf@sama5d33ek' configuration Trying 'fdt_sama5d33ek@1' fdt subimage Description: Flattened Device Tree blob for SAMA5D33EK Type: Flat Device Tree Compression: uncompressed Data Start: 0x2239cb24 Data Size: 33226 Bytes = 32.4 KiB Architecture: ARM Hash algo: crc32 Hash value: 8c9ac819 Verifying Hash Integrity ... crc32+ OK Booting using the fdt blob at 0x2239cb24 Loading Kernel Image ... OK Loading Device Tree to 3fb3f000, end 3fb4a1c9 ... OK Starting kernel ... Booting Linux on physical CPU 0x0 Linux version 4.9.87-linux4sam_5.8-00009-g084ae636406e (ilko@ubox) (gcc version 4.9.3 20150303 (release) [ARM/embedded-4_9-bra nch revision 221220] (GNU Tools for ARM Embedded Processors) ) #1 Wed Jun 6 16:15:41 CEST 2018 CPU: ARMv7 Processor [410fc051] revision 1 (ARMv7), cr=10c53c7d CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache OF: fdt:Machine model: Atmel SAMA5D33-EK cma: Reserved 64 MiB at 0x38000000 Memory policy: Data cache writeback CPU: All CPU(s) started in SVC mode. Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129920 Kernel command line: console=ttyS0,115200 earlyprintk mtdparts=atmel_nand:256k(bootstrap)ro,512k(uboot)ro,512k(uboot_redundent 1)ro,512k(uboot_redundent2)ro,256K(env),256k(env_redundent),256k(spare),512k(dtb),6M(kernel)ro,512k(dtb_redundent),6M(kernel_r edundent)ro,-(rootfs) rootfstype=ubifs ubi.mtd=11 root=ubi0:rootfs PID hash table entries: 2048 (order: 1, 8192 bytes) Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 443780K/524288K available (6144K kernel code, 209K rwdata, 1068K rodata, 1024K init, 195K bss, 14972K reserved, 65536K cma-reserved) Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xffc00000 - 0xfff00000 (3072 kB) vmalloc : 0xe0800000 - 0xff800000 ( 496 MB) lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) modules : 0xbf000000 - 0xc0000000 ( 16 MB) .text : 0xc0008000 - 0xc0700000 (7136 kB) .init : 0xc0900000 - 0xc0a00000 (1024 kB) .data : 0xc0a00000 - 0xc0a34528 ( 210 kB) .bss : 0xc0a34528 - 0xc0a654d0 ( 196 kB) NR_IRQS:16 nr_irqs:16 16 clocksource: pit: mask: 0xfffffff max_cycles: 0xfffffff, max_idle_ns: 14479245754 ns sched_clock: 32 bits at 100 Hz, resolution 10000000ns, wraps every 21474836475000000ns Console: colour dummy device 80x30 Calibrating delay loop... 351.43 BogoMIPS (lpj=1757184) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) CPU: Testing write buffer coherency: ok Setting up static identity map for 0x20100000 - 0x20100058 devtmpfs: initialized VFP support v0.3: implementor 41 architecture 2 part 30 variant 5 rev 1 clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns futex hash table entries: 256 (order: -1, 3072 bytes) pinctrl core: initialized pinctrl subsystem NET: Registered protocol family 16 DMA: preallocated 256 KiB pool for atomic coherent allocations cpuidle: using governor menu AT91: PM: standby: standby, suspend: ulp0 gpio-at91 fffff200.gpio: at address e0816200 gpio-at91 fffff400.gpio: at address e0818400 gpio-at91 fffff600.gpio: at address e081a600 gpio-at91 fffff800.gpio: at address e081c800 gpio-at91 fffffa00.gpio: at address e081ea00 pinctrl-at91 ahb:apb:pinctrl@fffff200: initialized AT91 pinctrl driver clocksource: tcb_clksrc: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 115833966437 ns at_hdmac ffffe600.dma-controller: Atmel AHB DMA Controller ( cpy set slave sg-cpy ), 8 channels at_hdmac ffffe800.dma-controller: Atmel AHB DMA Controller ( cpy set slave sg-cpy ), 8 channels AT91: Detected SoC family: sama5d3 AT91: Detected SoC: sama5d33, revision 2 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb at91_i2c f0014000.i2c: using dma0chan0 (tx) and dma0chan1 (rx) for DMA transfers at91_i2c f0014000.i2c: AT91 i2c bus driver (hw version: 0x402). at91_i2c f0018000.i2c: using dma0chan2 (tx) and dma0chan3 (rx) for DMA transfers at91_i2c f0018000.i2c: AT91 i2c bus driver (hw version: 0x402). media: Linux media interface: v0.10 Linux video capture interface: v2.00 Advanced Linux Sound Architecture Driver Initialized. clocksource: Switched to clocksource tcb_clksrc NET: Registered protocol family 2 TCP established hash table entries: 4096 (order: 2, 16384 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) UDP hash table entries: 256 (order: 0, 4096 bytes) UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) NET: Registered protocol family 1 RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. workingset: timestamp_bits=14 max_order=17 bucket_order=3 io scheduler noop registered (default) f0020000.serial: ttyS2 at MMIO 0xf0020000 (irq = 24, base_baud = 4125000) is a ATMEL_SERIAL ffffee00.serial: ttyS0 at MMIO 0xffffee00 (irq = 33, base_baud = 8250000) is a ATMEL_SERIAL console [ttyS0] enabled [drm] Initialized brd: module loaded loop: module loaded ssc f0008000.ssc: Atmel SSC device at 0xe0880000 (irq 20) atmel_nand_nfc 70000000.nfc: NFC is probed. atmel_nand 60000000.nand: Using dma0chan4 for DMA transfers. nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda nand: Micron MT29F2G08ABAEAWP nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 atmel_nand 60000000.nand: Use On Flash BBT atmel_nand 60000000.nand: minimum ECC: 4 bits in 512 bytes atmel_nand 60000000.nand: Initialize PMECC params, cap: 8, sector: 512 Bad block table not found for chip 0 Bad block table not found for chip 0 Scanning device for bad blocks random: fast init done Bad block table written to 0x00000ffe0000, version 0x01 Bad block table written to 0x00000ffc0000, version 0x01 12 cmdlinepart partitions found on MTD device atmel_nand Creating 12 MTD partitions on "atmel_nand": 0x000000000000-0x000000040000 : "bootstrap" 0x000000040000-0x0000000c0000 : "uboot" 0x0000000c0000-0x000000140000 : "uboot_redundent1" 0x000000140000-0x0000001c0000 : "uboot_redundent2" 0x0000001c0000-0x000000200000 : "env" 0x000000200000-0x000000240000 : "env_redundent" 0x000000240000-0x000000280000 : "spare" 0x000000280000-0x000000300000 : "dtb" 0x000000300000-0x000000900000 : "kernel" 0x000000900000-0x000000980000 : "dtb_redundent" 0x000000980000-0x000000f80000 : "kernel_redundent" 0x000000f80000-0x000010000000 : "rootfs" atmel_spi f0004000.spi: DMA TX channel not available, SPI unable to use DMA atmel_spi f0004000.spi: Atmel SPI Controller using PIO only m25p80 spi32766.0: at25df321a (4096 Kbytes) atmel_spi f0004000.spi: Atmel SPI Controller version 0x213 at 0xf0004000 (irq 19) libphy: Fixed MDIO Bus: probed CAN device driver interface macb f0028000.ethernet: invalid hw address, using random libphy: MACB_mii_bus: probed Micrel KSZ9021 Gigabit PHY f0028000.ethernet-ffffffff:01: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=f 0028000.ethernet-ffffffff:01, irq=102) macb f0028000.ethernet eth0: Cadence GEM rev 0x00020119 at 0xf0028000 irq 41 (2a:22:db:2b:88:88) ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci-atmel: EHCI Atmel driver atmel-ehci 700000.ehci: EHCI Host Controller atmel-ehci 700000.ehci: new USB bus registered, assigned bus number 1 atmel-ehci 700000.ehci: irq 43, io mem 0x00700000 atmel-ehci 700000.ehci: USB 2.0 started, EHCI 1.00 usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: EHCI Host Controller usb usb1: Manufacturer: Linux 4.9.87-linux4sam_5.8-00009-g084ae636406e ehci_hcd usb usb1: SerialNumber: 700000.ehci hub 1-0:1.0: USB hub found hub 1-0:1.0: 3 ports detected ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver ohci-atmel: OHCI Atmel driver at91_ohci 600000.ohci: failed to find sfr node at91_ohci 600000.ohci: USB Host Controller at91_ohci 600000.ohci: new USB bus registered, assigned bus number 2 at91_ohci 600000.ohci: irq 43, io mem 0x00600000 usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: USB Host Controller usb usb2: Manufacturer: Linux 4.9.87-linux4sam_5.8-00009-g084ae636406e ohci_hcd usb usb2: SerialNumber: at91 hub 2-0:1.0: USB hub found hub 2-0:1.0: 3 ports detected usbcore: registered new interface driver cdc_acm cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters usbcore: registered new interface driver usb-storage usbcore: registered new interface driver usbserial usbcore: registered new interface driver usbserial_generic usbserial: USB Serial support registered for generic usbcore: registered new interface driver ftdi_sio usbserial: USB Serial support registered for FTDI USB Serial Device usbcore: registered new interface driver pl2303 usbserial: USB Serial support registered for pl2303 qt1070 1-001b: can not read register, returned -121 qt1070 1-001b: ID -121 not supported rtc rtc0: alarm rollover not handled rtc rtc0: invalid alarm value: 1900-1-1 0:0:0 at91_rtc fffffeb0.rtc: rtc core: registered fffffeb0.rtc as rtc0 at91_rtc fffffeb0.rtc: AT91 Real Time Clock driver. i2c /dev entries driver AT91: Starting after wakeup at91_wdt fffffe40.watchdog: watchdog is disabled at91_wdt: probe of fffffe40.watchdog failed with error -22 sdhci: Secure Digital Host Controller Interface driver sdhci: Copyright(c) Pierre Ossman atmel_mci f0000000.mmc: version: 0x505 atmel_mci f0000000.mmc: using dma0chan5 for DMA transfers atmel_mci f0000000.mmc: Atmel MCI controller at 0xf0000000 irq 18, 1 slots atmel_mci f8000000.mmc: version: 0x505 atmel_mci f8000000.mmc: using dma1chan0 for DMA transfers atmel_mci f8000000.mmc: Atmel MCI controller at 0xf8000000 irq 25, 1 slots sdhci-pltfm: SDHCI platform and OF driver helper ledtrig-cpu: registered to indicate activity on CPUs atmel_aes f8038000.aes: version: 0x135 atmel_aes f8038000.aes: Atmel AES - Using dma1chan1, dma1chan2 for DMA transfers atmel_sha f8034000.sha: version: 0x410 atmel_sha f8034000.sha: using dma1chan3 for DMA transfers atmel_sha f8034000.sha: Atmel SHA1/SHA256/SHA224/SHA384/SHA512 atmel_tdes f803c000.tdes: version: 0x701 atmel_tdes f803c000.tdes: using dma1chan4, dma1chan5 for DMA transfers atmel_tdes f803c000.tdes: Atmel DES/TDES usbcore: registered new interface driver usbhid usbhid: USB HID core driver iio iio:device0: Resolution used: 12 bits input: at91_adc as /devices/platform/ahb/ahb:apb/f8018000.adc/input/input0 0-001a supply DCVDD not found, using dummy regulator 0-001a supply DBVDD not found, using dummy regulator 0-001a supply AVDD not found, using dummy regulator 0-001a supply CPVDD not found, using dummy regulator 0-001a supply MICVDD not found, using dummy regulator wm8904 0-001a: revision A atmel-wm8904-audio sound: wm8904-hifi <-> f0008000.ssc mapping ok NET: Registered protocol family 10 sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver NET: Registered protocol family 17 can: controller area network core (rev 20120528 abi 9) NET: Registered protocol family 29 can: raw protocol (rev 20120528) can: broadcast manager protocol (rev 20161123 t) can: netlink gateway (rev 20130117) max_hops=1 ubi0: default fastmap pool size: 95 ubi0: default fastmap WL pool size: 47 ubi0: attaching mtd11 random: crng init done ubi0: scanning is finished ubi0: volume 0 ("rootfs") re-sized from 367 to 1878 LEBs ubi0: attached mtd11 (name "rootfs", size 240 MiB) ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 ubi0: good PEBs: 1920, bad PEBs: 4, corrupted PEBs: 0 ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128 ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 590959312 ubi0: available PEBs: 0, total reserved PEBs: 1920, PEBs reserved for bad PEB handling: 36 at91_rtc fffffeb0.rtc: setting system clock to 2007-01-01 00:00:10 UTC (1167609610) ALSA device list: #0: wm8904 @ SAMA5D3EK ubi0: background thread "ubi_bgt0d" started, PID 104 UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "rootfs", R/O mode UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes UBIFS (ubi0:0): FS size: 237064192 bytes (226 MiB, 1867 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs) UBIFS (ubi0:0): reserved for root: 0 bytes (0 KiB) UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID 3256C183-26FC-4287-B7A3-A8C291E3364F, small LPT model VFS: Mounted root (ubifs filesystem) readonly on device 0:13. devtmpfs: mounted Freeing unused kernel memory: 1024K UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 107 Starting logging: OK Starting portmap: done Initializing random number generator... done. Starting network... Generating RSA Key... Generating public/private rsa1 key pair. Your identification has been saved in /etc/ssh_host_key. Your public key has been saved in /etc/ssh_host_key.pub. The key fingerprint is: 59:0b:15:86:56:52:27:c3:b2:da:4c:a6:6c:40:19:f3 The key's randomart image is: +--[RSA1 2048]----+ | oo .=O.. | | oo ++.+ | | . E..o. | | . ++ . | | o BS . | | = o | | . | | | | | +-----------------+ Generating RSA Key... Generating public/private rsa key pair. Your identification has been saved in /etc/ssh_host_rsa_key. Your public key has been saved in /etc/ssh_host_rsa_key.pub. The key fingerprint is: 9b:50:c2:34:fa:4a:a4:72:2f:df:48:f4:52:92:f3:23 The key's randomart image is: +--[ RSA 2048]----+ | o | | + . | | o o . | | o o o | |. o * + S | | o + B . o | | . E + o | | + = . | | o . | +-----------------+ Generating DSA Key... Generating public/private dsa key pair. Your identification has been saved in /etc/ssh_host_dsa_key. Your public key has been saved in /etc/ssh_host_dsa_key.pub. The key fingerprint is: 79:71:1f:76:9a:df:95:4f:29:e8:2c:77:dd:77:9d:b6 The key's randomart image is: +--[ DSA 1024]----+ | | | | | . . o .| | . o.o =o| | S .. .+oo| | .o ooB| | . + . +O| | o . . +| | E | +-----------------+ Generating ECDSA Key... Generating public/private ecdsa key pair. Your identification has been saved in /etc/ssh_host_ecdsa_key. Your public key has been saved in /etc/ssh_host_ecdsa_key.pub. The key fingerprint is: 56:2c:c2:1b:3c:67:fb:96:9f:d6:90:37:5a:3a:f6:bc The key's randomart image is: +--[ECDSA 256]---+ | | | o . | | * + o | | B + | | . S . | | . . .o + | | + B . | | . .*o. | | oooE. | +-----------------+ Generating ed25519 Key... Generating public/private ed25519 key pair. Your identification has been saved in /etc/ssh_host_ed25519_key. Your public key has been saved in /etc/ssh_host_ed25519_key.pub. The key fingerprint is: 20:7f:d9:3c:37:cb:1d:87:38:42:75:b5:4e:4b:07:e5 The key's randomart image is: +--[ED25519 256--+ | . ooo| | . . o.| | . . . +E| | o . = .+.o| | . S = = oo.| | . = = o | | o . | | | | | +-----------------+ Starting sshd: OK Welcome to Buildroot buildroot login: